This website requires JavaScript.
Coupons
Help

Secrets of CNC machining of high hardness stainless steel Cracking the problems of tool wear and work hardening

Blog  /  Secrets of CNC machining of high hardness stainless steel Cracking the problems of tool wear and work hardening

Secrets of CNC machining of high hardness stainless steel Cracking the problems of tool wear and work hardening

Jun 04,2025

High-hardness stainless steel (e.g. 304, 316, 17-4PH, etc.) is widely used in aerospace, medical device and automotive manufacturing due to its corrosion resistance, strength and aesthetics. However, problems such as fast tool wear and severe work hardening during its machining process have become bottlenecks in manufacturing efficiency and cost control. This paper provides systematic solutions from the dimensions of material properties, process optimisation, intelligent monitoring and so on, combined with the industry's latest technology.

CNC machining of high hardness stainless steel



I. In-depth analysis of high hardness stainless steel processing difficulties

1. machining hardening mechanism of

high hardness stainless steel in the cutting process due to plastic deformation, surface grain refinement and the formation of hardened layer (hardness enhancement of 20% -30%), resulting in increased resistance to subsequent cutting, shortening the life of the tool.

For example, the hardness of 304 stainless steel after hardening can reach more than HV300, tool wear rate increased by 50%.

2. Heat accumulation and sticky knife effect

Poor thermal conductivity: stainless steel thermal conductivity is only 1/3-1/4 of carbon steel, cutting zone temperature up to 1000 ℃, accelerating tool oxidation and coating flaking.

Chip sticking: high temperature chips are easy to adhere to the front face of the tool, the formation of chip tumour, resulting in deterioration of surface roughness (Ra>1.6μm).

3. Impact of material microscopic characteristics

Austenitic stainless steel (such as 316) due to high nickel content, machining is easy to produce long chips, chip removal difficulties; martensitic stainless steel (such as 17-4PH) with high hardness (HRC ≥ 40), the tool impact resistance requirements are stringent.


II. Tool selection and coating technology optimisation

1. Tool material matching

Material typeApplicable SceneAdvantage
Cemented carbide (YG8)General-purpose machining (e.g. milling, drilling)Cost-effective and resistant to plastic deformation
CBN (cubic boron nitride)High hardness stainless steel finishing (e.g. 17-4PH)Wear resistance 5-10 times that of cemented carbide, life expectancy 3 times higher
Ceramic toolHigh speed cutting (line speed ≥200m/min)High temperature resistance (1200℃), low coefficient of friction

2. Coating technology comparison

TiAlN coating: excellent high temperature resistance, cutting speed can be increased by 20%, suitable for intermittent cutting scenarios.

Diamond coating: surface friction coefficient reduced by 40%, suitable for high-precision machining (Ra≤0.4μm).

Multi-layer composite coatings (e.g. AlTiN+MoS2): both wear resistance and self-lubrication, tool life extended by 50%.

3. Geometrical parameter design strategy

Front Angle Optimisation: Increase the front angle (10°-20°) to reduce cutting force and inhibit work hardening.

Edge Strengthening: Use chamfering or passivation treatment (passivation amount 0.02-0.05mm) to reduce the risk of chipping.

Chipbreaker design: V-shaped chipbreaker (width 0.2-0.4mm) can segment chips to improve chip removal efficiency.


III. Optimisation programme for the whole process of machining

1. Scientific matching of cutting parameters

Machining stageCutting speed (m/min)Feed (mm/r)Back draft (mm)Cooling mode
Roughing50-800.1-0.22-4High pressure internal cooling (7MPa)
Finishing80-1200.05-0.10.1-0.5Micro Quantity Lubrication (MQL)

2. Cooling and lubrication innovative technologies

High-pressure internal cooling system: the coolant reaches the cutting area directly, the cooling effect is increased by 40%, and the tool life is extended by 30%.

Low Temperature Cold Air Technology: Adopting -50℃ cold air injection to inhibit material rebound and reduce surface roughness by 50%.

Nano-fluid lubrication: cutting fluid with added copper nanoparticles reduces friction coefficient by 25% and cutting force by 15%.

3. Vibration suppression and process stability

Variable Depth of Cut: By periodically adjusting the back draft (±0.05mm), the cutting load is dispersed and the vibration is reduced by 60%.

Damped tool system: Built-in vibration damper (damping ratio ≥ 0.1), suppressing high-frequency chatter and improving machining accuracy to ±0.01mm.


IV. Industry cutting-edge technology and development trend

1. Intelligent machining monitoring

AI process optimisation: real-time analysis of cutting force, temperature and vibration data through machine learning, dynamic adjustment of parameters, efficiency increased by 20%.

Digital twin technology: build virtual machining model, predict tool wear and deformation risk, yield rate increased from 95% to 99.5%.

2. Green Manufacturing Technology

Scrap recycling and regeneration: Stainless steel scrap is regenerated by hydrogenated dehydrogenation (HDH) process with oxygen content ≤ 0.15%, which can be reused in powder metallurgy.

Dry cutting technology: adopting super-hard cutting tools (e.g. CBN) with cold air cooling, completely abandoning cutting fluid and reducing carbon emission by 60%.

3. Composite machining processes

Laser-assisted cutting: laser preheating softens the surface layer of the material (temperature 400-600°C), cutting force is reduced by 30%, and tool life is extended by two times.

Ultrasonic vibration machining: 20kHz high-frequency vibration superposition, chip thickness reduced by 50%, surface roughness up to Ra0.2μm.


V. Quality control and industry application cases

1. Surface treatment and inspection

Electrolytic polishing: Nitric acid-Hydrofluoric acid mixture (concentration 10%-15%) removes the hardened layer, corrosion resistance increased by 30%.

X-ray residual stress analysis: detect the residual stress distribution on the surface to avoid fatigue cracks caused by work hardening.

2. Successful cases

Medical device field: a company processing 316L orthopaedic implants, using CBN tools + high-pressure internal cooling process, the yield rate increased from 85% to 99%, cost reduction of 25%.

Automotive industry: a car enterprise processing 17-4PH turbine housing, through laser-assisted cutting technology, the processing cycle is shortened by 40%, and the surface roughness is stable at Ra0.4μm.

Contact JLCCNC today to unlock the new world of high hardness stainless steel machining!


cnc machining quote